Wednesday, July 13, 2016

Project of the Week

Well, it's no so much the project of the week as the parts of the week I've been making for my Grizzly CNC conversion project.  It's that enormous X-axis end cap I've been talking about.

Let me bottom line/short version the story first.  I've got a decent Rev 1 set of parts close to finished and they look like they'll work.  Yes, there are some goof-ups in there, but I don't think there's anything insurmountable.  First, the two piece end cap.
This is a half inch thick piece mounted on top of another half inch piece, and held together by the two black screws at the 2 and 10 o'clock positions of the big bearings.  The bearings fit perfectly.  The next part is a motor mount and stepper motor support that mount on top of this.  The motor mount's bore is considerably smaller than the bearings, sized 0.800" while the outer bore at the bearings is 1.024".  The motor mount compresses the bearings to help control backlash.

I started with the drawings that I purchased for the end cap, and then split them in two.  One became the small top piece while the other became the big bottom.  I partitioned features between them so that when the two pieces are joined, the result should be the same as the one piece end cap.  For example the original part had a dual diameter bore for the bearings: 1.024" that went down 0.638" and the rest of the hole is 0.875".  I split that into the top and bottom pieces, so the top is the larger diameter and the bottom piece has two diameters.

The goof up concerns those three holes around the bearings you can see in the top piece.  Those are not threaded and are sized to clear an 8-32 screw.   The base of the end cap (the large rectangle) has those holes threaded.  I moved them down from the top piece without it registering in my mind that the screws need to thread into the bottom piece but can't because they're not long enough to make it to the bottom piece.  What I missed is that motor mount I mentioned that goes on top of this piece.  The stack up looks like this (the parts are just stacked - no fasteners). 
The motor mount is 3/8" thick, the top of the end cap is 1/2", so a screw has to go through 7/8" of metal before it gets to the threaded holes, and you'd want some engagement there, like another quarter inch (1 1/8).  So instead of 3/4" screws, I need three longer screws.  No big deal.

There's another problem lurking in this piece, which is that when I transferred the base (7x2 piece) from the Sherline, where I drilled all the holes, onto the big mill for boring the holes, I flipped it upside down!  So the view you're seeing is supposed to be, and now is, the top, but the two mounting holes left and right of the 1" thick area are counterbored on the bottom.  That's also probably going to be fixed by two new screws. 

This part doesn't have the stylin' tapers that the original part I started from has.  I'll have to see if I can figure out how to add those without barfing anything up. 
Every part's a puzzle.


3 comments:

  1. Good to see you're feeling well enough to get back in the shop.

    I've been crawling on, over, around, and under my Supra for most of the week!

    ReplyDelete
    Replies
    1. Absolutely, it's good to be able to spend hours in the shop again. Strangely, though, it kinda tires me out after four or five hours these days. The voices in my head try to tell me I should start "working out" again, but I manage to forget pretty regularly.

      As for crawling on, over, around, under my cars: no thanks. It's true it usually stays under 100 here, especially if we get a strong sea breeze, but mid-90s and our humidity is no fun either. I needed to wash and wax the cars back before the surgery. It'll be a few weeks (September?) before I'm up to it, I think.

      Delete
  2. Yeah, crawling around on cars is no fun when it's hot/humid outside.

    I won a $100 gift certificate to HRO last week at the QCWA lunch.

    I'm going apply it towards an "SDRPlay" receiver, so watch for a review sometime soon....

    ReplyDelete