I don't have much comment because there has been no official story on this, and this video comes from the forums on NASA Spaceflight. That link will take you to the end of the thread, which goes back to last summer. Currently that's page 89 and the accident seems to have happened during page 87. There are interesting pictures of the wreckage taken this morning in daylight.
Just three days ago, on the 26th, Teslarati was excited that SN1 had been rolled to the test stand and mounted. There is no coverage of this accident, but perhaps the fact that it happened on Friday night means the staff was off and they don't work weekends.
The forum at NASA Spaceflight has idle speculation on what the cause of the problem could be, but until some sort of investigation is completed, that's just speculation. First law of breaking news applies here: the first reports are always wrong.
In totally unrelated SpaceX news, Monday's planned Falcon9 launch of a resupply cargo capsule for the ISS has been delayed until the Friday, the 6th. The reason is pretty remarkable and the only reason a launch delay is worth mentioning.
During tests of the system that was considered ready to launch, a problem was found in the second stage. Thanks to their aggressive launch cadence, they have plenty of hardware and chose to just replace the second stage with another that was scheduled for a Starlink internet satellite launch.
“SpaceX identified a valve motor on the second stage engine behaving not as expected and determined the safest and most expedient path to launch is to utilize the next second stage in line that was already at the Cape and ready for flight. The new second stage has already completed the same preflight inspections with all hardware behaving as expected. The updated target launch date provides the time required to complete preflight integration and final checkouts.”Given the complexity of an orbital rocket's upper stage, it's a safe bet it takes a couple of months to build one and get it ready for flight. To replace an upper stage and just delay a launch a few days can only mean they basically had one there on the Cape ready to fly. NASA gets what's likely the safest scenario, replace the upper stage entirely, and SpaceX can troubleshoot this upper stage as they feel is best.
NASA.gov — February 25th, 2020
This comment has been removed by a blog administrator.
ReplyDeleteThere are reports of a Musk tweet stating that they didn't have their welding setup settings correct for much of SN1. This has been fixed for SN2, but I suppose it's possible it had something to do with it. It will likely be awhile before we know the root cause of this one.
ReplyDeleteThe comments on NASA Spaceflight centered on welding, with some people saying they can't possibly get good welds in the conditions they were working in. I'm skeptical of that, but it is a marine atmosphere so I'm sure there's some amount of salt in the air. I just don't know what precautions they take.
DeleteIt's interesting that they were already working on SN2 before this test even started. Iterate, fail early, fix continuously.
IIRC, they were also using the wrong welding gasses/temperatures/etc, which was embrittling the material they were working on.
ReplyDeleteThey called it a "proof" test. IIRC, in a proof test (up to design limits), the test article is supposed to survive. A burst test would be a destructive test.
MadRocketSci
Unlike NASA/Boeing, they'll back up and build another. Probably need to slow down and think it through/do it carefully though. A full tilt rush to throw something, anything, together for a photoop isn't conducive to the delicate construction needed to assemble a vehicle that lightweight/thin-walled.
ReplyDeleteTelsarati posts an article about it today in which they call it a proof test and comment " SpaceX is likely somewhat surprised about the outcome of SN01’s first proof test."
ReplyDeleteIt may have not been the goal for a proof test, but they should absolutely expect and plan for failure of the vehicle. That's because of the word "test" in there.
A couple of things that have come out from SpaceX. Elon Musk tweeted something about the thrust puck being a problem. Also he tweeted out something about weld planishing. After having looked up what planishing is, how they will accomplish that for the welds on a near complete Starship or Superheavy will be amazing. I can see them doing a few rings but all of the welds on the whole thing?
ReplyDeleteThis comment has been removed by a blog administrator.
ReplyDelete